Lc2i Pro Tuning . AudioControl LC2i PRO 2 Channel Line Output Convertor + AccuBass Amp is a Pioneer GM-D8601, sub is Pioneer TS-SW2502S4 (The light can blink but not stay on) I connected my subs and played this song "Sleezy Flow (remix)"
LC2i PRO AudioControl from www.audiocontrol.com
LC2i Pro - Slowly turn AccuBASS Threshold to the right (clockwise) until the status LED illuminates and you hear hear bass being restored If the Maximized Light turns on, the LC2i PRO output is distorting
LC2i PRO AudioControl I adjusted the LC2i to where I thought it should be and proceeded to adjust the amp (with the high pass filter on) as per instructions. I had my same setup in my previous 2013 S4 with the B&O system and it sounded better along with being waaaaay easier to tune Then measure on the speaker outputs of the amplifier while you set the gain for both the lc2i and the amplifier
Source: www.desertcart.ae AudioControl LC2i PRO 2Channel Line Output Converter with Impedance , Then measure on the speaker outputs of the amplifier while you set the gain for both the lc2i and the amplifier Cut up a trash RCA connector or just touch the multimeter leads to the RCA inside and outside
Source: krankitup.com AudioControl LC2i Pro , getting close to clipping the output of the LC2i PRO I had my same setup in my previous 2013 S4 with the B&O system and it sounded better along with being waaaaay easier to tune
Source: radiowaves.co.za LC2i Pro 2 Channel Line Out Converter Audiocontrol , I've spent a ton of time messing with adjustments to get it to sound good but it sincerely makes. I myself have the LC2i Pro, with amp gain at 0, I set the AC LC2i Pro bass level output with a 50 hz -10 db or -5 sine wave until the AC Lc2i pro maximum light lit up, I than.
Source: www.audiocontrol.com LC2i PRO AudioControl , LC2i Pro - Slowly turn AccuBASS Threshold to the right (clockwise) until the status LED illuminates and you hear hear bass being restored Didn't notice any bass roll off from the factory head unit so the bass threshold and accubass are set accordingly as per instructions on the LC2i
Source: www.bestbuy.com Customer Reviews AudioControl 2Channel Active Line Output Converter , With a pure sine wave tone, the multimeter will register AC. Generally you will have your head unit up to 3/4 volume (LC2i disconnected from amp - amp gains all the way down).
Source: www.youtube.com The new bench mark in High to low level adapters from AudioControl LC2i , I myself have the LC2i Pro, with amp gain at 0, I set the AC LC2i Pro bass level output with a 50 hz -10 db or -5 sine wave until the AC Lc2i pro maximum light lit up, I than backed it off a hair Think of the AccuBASS Level setting as a bass boost feature as it is.
Source: www.audiocontrol.com LC2i PRO AudioControl , With a pure sine wave tone, the multimeter will register AC. Didn't notice any bass roll off from the factory head unit so the bass threshold and accubass are set accordingly as per instructions on the LC2i
Source: www.ebay.com Audiocontrol LC2i Pro Black 2 Channel Line Output Converter W/ Accubass , My F150 doesnt seem to have any bass rolloff, so I am leaving the Accubass threshold UP, and the Accubass knob DOWN Play 50Hz, 60Hz, etc pure sine tones from your head unit and turn the volume up and down
Source: www.rav4world.com AudioControl LC2i 2channel LineOut Converter with AccuBASS™ Black , Tuning the amp and LC2i is simply put, a pain in the ass!!!! The Bose system is definitely a chore to work with and tune I've spent a ton of time messing with adjustments to get it to sound good but it sincerely makes.
Source: skyhighcaraudio.com Audio Control LC2i PRO , My F150 doesnt seem to have any bass rolloff, so I am leaving the Accubass threshold UP, and the Accubass knob DOWN This video focuses on tips and tricks for getting the best sound possible out of your LC2i Pro or LC2i in your upgraded car audio setup
Source: www.youtube.com LC2i Pro Shared Power & Ground with Amplifier plus Remote Turn On 💯 , Play 50Hz, 60Hz, etc pure sine tones from your head unit and turn the volume up and down Turn the output level down until the Maximized Light turns off
Source: www.youtube.com Add amplifiers like a PRO! AudioControl LC2iPRO overview YouTube , Turn the output level down until the Maximized Light turns off I adjusted the LC2i to where I thought it should be and proceeded to adjust the amp (with the high pass filter on) as per instructions.
Source: www.walmart.com AudioControl LC2i PRO 2Channel Line Output Converter with Impedance , Think of the AccuBASS Level setting as a bass boost feature as it is adjusting how much bass is. Start with the amp gain all the way down and then start turning the bass output (not accubass) dial on the lc2i up until you reach your desired voltage out of the amp, or until the maximized light on the lc2i.
Source: www.audiocontrol.com LC2i PRO AudioControl , getting close to clipping the output of the LC2i PRO Hook a multimeter on AC voltage mode to one of the RCA outs of the LC2i
Source: www.audiocontrol.com LC2i PRO AudioControl , (The light can blink but not stay on) I connected my subs and played this song "Sleezy Flow (remix)" Cut up a trash RCA connector or just touch the multimeter leads to the RCA inside and outside
The new bench mark in High to low level adapters from AudioControl LC2i . This video focuses on tips and tricks for getting the best sound possible out of your LC2i Pro or LC2i in your upgraded car audio setup I've spent a ton of time messing with adjustments to get it to sound good but it sincerely makes.
The new bench mark in High to low level adapters from AudioControl LC2i . Cut up a trash RCA connector or just touch the multimeter leads to the RCA inside and outside Amp is a Pioneer GM-D8601, sub is Pioneer TS-SW2502S4